Introduction

Gathering debugging information is vital information for developers to have, in order to fix wireless driver bugs. This process helps improves the overall quality of wireless drivers.

Debugging information to provide in your report

First, plese note "I don't know", "I haven't tested this", "I'll test later", "I'm assuming that...", etc. are not acceptable answers to any of the below. If you don't understand the question, or have to assume something, please advise to what you don't understand or are assuming specifically in your report, and it will be clarified. Otherwise, making such a response will further delay your issue being addressed.

As well, please post in your report both the question and answer, as the presentation of the information here can change:

1. What is the full computer model number (ex. HP G32-301TX Notebook PC)?

2. If you update your BIOS to the newest version following the guide here, does this change anything?

3. Regarding your wireless Access Point (AP):

   • 3a. What is the current AP manufacturer, full model, revision, and firmware version?
     3b. If you update the AP to the latest firmware does it change anything?
     3c. What wireless connection type are you using (802.11n, 802.11g, etc.)?
     3d. If you switch to 802.11g (or 802.11n if you are using 802.11g) does this change anything?
     3e. What channel specifically are you using when this problem is reproducible?
     3f. In order to understand the wireless environment your AP is working in, please provide the output of the following terminal command:

     sudo iw dev wlan0 scan | grep -i "ds parameter set"

     3g. What encryption type are you using (ex. WEP, WPA2-PSK, etc.)?
     3h. If you change and remove encryption entirely does this change anything?
     3i. Do you have QoS (Quality of Service)/WMM (Wi-Fi Multimedia) enabled?
     3j. If you disable/enable QoS/WMM does it change anything?
     3k. What is the current beacon interval (usually default is 100)?
     3l. If you adjust this to 50 does it change anything?
     3m. Does your AP have a firewall enabled?
     3n. If you enable/disable the firewall does it change anything?
     

4. Does another wireless device tested with the AP have the same problem as the hardware you initially reported with?
5. What is the distance of the wireless device from the AP?
6. What is the number and type of obstructions between your device and the AP?
   • 6a. If you bring the device close to the AP and eliminate obstructions, does this change anything?
7. Does the issue occur with different APs?

8. Is it a regression (i.e. did the problem happen in a prior Ubuntu release)? If so, what release specifically did it last work with? If you do not know, could you please test for this in the earliest release of Ubuntu that is supported as per Ubuntu Releases?

9. Could you please test upstream's compat-wireless backports via https://wiki.ubuntu.com/Kernel/LinuxWireless#Compat-wireless_from_upstream? Please mention in your report the specific version you tested.

10. If the above backport did work, does this problem occur in the newest mainline kernel following https://wiki.ubuntu.com/Kernel/MainlineBuilds? Please mention what specific version of the mainline kernel you tested with in your report.

11. If the mainline works, does either the development release or the Ubuntu provided stable compat-wireless backport work following https://wiki.ubuntu.com/Kernel/LinuxWireless#Compat-wireless_in_Ubuntu? Please mention in your report the specific version you tested.

12. Only for Broadcom wireless chipsets, does the Broadcom STA driver work following https://help.ubuntu.com/community/WifiDocs/Driver/bcm43xx? Please mention what specific version of Broadcom STA you tested with in your report.

13. Only for Realtek wireless chipsets, does the upstream Realtek drivers downloaded from http://www.realtek.com.tw work? Please mention what specific version of the drivers you tested with in your report.

14. Only for Intel wireless chipsets:

    • Please advise to which firmware version the device is using.

      • Stating the linux-firmware version (ex. apt-cache policy linux-firmware), while necessary, is not the firmware version in use, but the package version of linux-firwmare. In order to find the version in use, one may check dmesg. For example, if the chipset was using the iwlwifi driver:

        cat /var/log/dmesg | grep "firmware version"
        [    2.820714] iwlwifi 0000:03:00.0: loaded firmware version 25.222.9.0 op_mode iwlmvm

        For more on this, please see here.

    • Did this work on a prior linux-firmware version? If you don't know, please test a prior release and advise to which version of the firmware, and kernel you tested specifically.

    • Does this work, or have a measurable positive impact using the latest firmware available from Intel? If you don't know, please test this with the latest mainline kernel, and firmware available for your chipset.

15. Does ndiswrapper work following https://help.ubuntu.com/community/WifiDocs/Driver/Ndiswrapper? Please mention what specific version of ndiswrapper you tested with, and a link to the Windows driver you used in your report. If ndiswrapper does not work, you are welcome to file a new bug report by executing at a terminal:

    ubuntu-bug ndiswrapper-utils-1.9

Compat-wireless from upstream

Upstream has a more bleeding-edge tree called linux-next, that uses the stable tree as it's base. One would want to test this, as it contains the latest features and fixes, and is a staging area for code that may be merged into Linus's tree. Testing this gives developers vital information on what may fix your issue. For more on this, please see here.

Installing compat-wireless from the Ubuntu repositories

The compat-wireless packages in Ubuntu are generated with select wireless commits from linus' stable tree. This provides one with the benefit of improved wireless functionality in a stable Ubuntu release, without adding any other, potentially unnecessary code. The following is a list of compat-wireless packages available from the Ubuntu repositories:

Precise - https://launchpad.net/ubuntu/+source/linux-backports-modules-3.0.0

Lucid - https://launchpad.net/ubuntu/+source/linux-backports-modules-2.6.32

For example, if one would like to install this in Precise, this may be done by executing the following at a terminal:

sudo apt-get -y install linux-backports-modules-cw-3.3-3.2.0.23-generic-pae

and then reboot.

You will probably get newer versions of this package if you enable the proposed repository as explained above.

While compat-wireless in Ubuntu is updated regularly, it may not be every day. If you want to ensure you are running the cutting edge, one would want to use compat-wireless from upstream.

Removing compat-wireless from the Ubuntu repositories

Please keep in mind that linux-backports-modules install modules in /lib/modules/$(uname -r)/updates/ and upon removal the modules are not removed. So be sure to rm -rf that updates directory (and only the updates directory!).

The Ubuntu proposed repository

Keep in mind Ubuntu has a "proposed" repository which allows you to get newer stable kernels (if you are using 2.6.27.10 the proposed repository may have a 2.6.27.14 kernel). Instructions on enabling this repository may be found here. The kernels are propagated over time from the proposed repository to updates over a few weeks period of time after general testing and acceptance.

The Linux wireless guide on reporting bugs

For debugging information preferred by upstream please see: http://wireless.kernel.org/en/users/Documentation/Reporting_bugs